Assembly/Test Technician III (CVN) - Honeywell Aerospace - Tempe, Arizona
(2022-09)
Manual assembly of CVN Production (Type 2,3,4,5) to ensure these items are within parameters to which the unit under test was designed.
- Using the Arbor Press and following Work Instructions begin installing non-traceable components into housing.
- Screening Assembly Components and document serial numbers in SAP and Travelers
- Assemble Main housing, to Traceable components (Gear set, position sensor, clutch assembly, tie rods, motor, DCI And Controller) Using Height gage, Calipers, Solder, Pin and Crimp.
- Assembly completed, Run Insulation Resistance and Dielectric Test
- Test Unit by the current Rev ATP
- Final Prep by checking Travelers and SAP, all serial numbers match, ever nut and bolt secured to spec, Laser print serial number and stamp out metal plate with Serial Number, Rev and Series.
Assembly/Test Technician III (Conveyor belt) - Honeywell Integrated - Tempe, Arizona
(2020-12 - 2022-09)
Manual assembly of Conveyor Belts
- Pressure and no pressure drills to insert guard rails and rollers
- Build all sub-assembly parts to specs and plans depending on size of conveyor
- Manually paint parts and rails with base and final colors per order
- Assis in inventory count
Quality Control Inspector - Inteplast Group/AmTopp - Phoenix, Arizona
(2016-12 - 2020-12)
Closely monitoring and examining each stage of the entire production process.
- Segregating non-conforming products in accordance with written quality procedures.
- Making sure all employees follow documented procedures and standards
- Overseeing all incoming material used on product to verify all are up to company specification.
- Respond to any customer complaints and take corrective action to fulfill all customer orders and correct issues.
- Using precision tools to quickly identify defective products
- Perform Daily audits an all production process to insure quality products and paper work is being documented correctly due.
Test Technician III (Radio Frequency) - Honeywell Aerospace - Deer Valley, Arizona
(2014-05 - 2016-01)
Manual Test of High Voltage assembly for the Avionics Radar Production to insure these items are within parameters to which the unit under test was designed.
- Troubleshooting by specifying the input and output Signal terminals using Spectrum Analyzers along with Oscilloscopes and Radar Tester RD-301.
- Screening components prior to install into sub-assemblies and testing for Insertion Loss Screening for Waveguide Assembly Components on Scalar Network Analyzer
- Loading Units into Burn in Chambers to verify reading Temperature cycles are within specification under hot and cold Cycle.
- Cross Trained in 787 production lines to Aid in testing Printed Board Assembly Along with the Sensor Production Line in Aid in testing Air Data Modules specifically running the Environmental Stress Screening on Vibration Table.
- Quality Control all finish test product to verify that it's working properly before moving on to the next operation.
Production Lead/Test Technician III - Jabil Circuit Solution - Tempe, Arizona
(2009-11 - 2012-05)
- Communicate essential issues to team members and/or facilitates team meetings
- Ensures operators are following proper ESD and safety practices.
- Writes discrepancy reports for scrap material and seeks appropriate signatures with assistance from PPA.
- Performs testing from established procedures and performs difficult electronic testing assignments
- Evaluates various types of electronic and mechanical products and designs complex electronic test equipment and fixtures as needed.
- Quality Control all finish test product to verify that it's working properly before moving on to the next operation.
Manufacturing Technician II - Medtronic Microelectronics Center - Tempe, Arizona
(2007-09 - 2008-10)
Manual attachment process that includes procedures for battery and reed switch attachment under a microscope.
- Using a Weller MT 1500 Hand soldering station.
- Perform a UV lamp monitor at the beginning of the shift to verify that the UV lamps is working effective and insure that the Camelot System 1818 Dispenser is working properly.
- Operating a pneumatic press to insert hard die coat (HDC) dams into printed wiring boards.
- Set up and operating of the Routing System, verify that any preventative maintenance (PM) and calibration stickers are valid at the beginning of each shift prior to use. Routing out specific components and excess rout path before Saw and Final inspection.
Test Technician I - Intel Corporation - Chandler, Arizona
(2006-06 - 2007-07)
Monitoring, controlling and operating computerized wafer, test probe and assemble equipment.
- Perform daily PM's to monitor the health of tools.
- Handling test wafer on an Opt Probe that is used to measure the film thickness along with a Surf scan that displays a three-dimensional view of the wafer to identify defects, contaminants and scratches.
- Obtain level one certification to run tool along with chemical and hazmat training.
- Performing Monitors, controlling and operating computerized wafer, test, probe and assemble equipment.
Casino Finance - Gila River Gaming Enterprise - Chandler, Arizona
(2002-12 - 2004-11)
Collection and counting of coins and currency from casino slot machines.
- Counting of redemption coins and poker chips.
- Follows all internal cash control policies and procedures set forth by the enterprise.
- Performs accurate data input and error corrections into computer logs.
- Safeguards casino bankroll and maintains an accurate accountability of all funds in the vault and main coin bank.
- Ensures that all currency, gaming chips and coin are kept at an optimum level to sufficiently operate the Casino
Electrical Technician/Quality Control - Shin-Etsu Semiconductor - Tempe, Arizona
(2000-01 - 2004-10)
Appling coating resins to packaging materials for encapsulating all types of semiconductor devices at board and component level.
- Performing stress test to insure that the coating was protecting the devices.
- Loading Units into Burn in Chambers to verify reading Temperature cycles are within specification under hot and cold Cycle.
- Inspecting and Packaging all materials for outbound delivery following all ESD Protocols.
