Skip to main content
Vivaan Jain

Vivaan Jain

Embedded Firmware Engineer

Talent
Noida, Sector 125Member since July 8, 2026
C++VerilogSPII2CUARTRS485TCP/IPEthernet4G LTERaspberry Pi 5Alpine LinuxEmbedded LinuxXilinx Artix-7 FPGAFreeRTOSAltium DesignerXilinx VivadoOscilloscopeLogic AnalyzerEmbedded FirmwarePeripheral DriversBare-MetalPCB DesignFPGA
·

Hire this person

Send a job offer directly to this candidate

C++VerilogSPII2CUART

About

Embedded Firmware Engineer with 2+ years of hands-on experience developing production-grade firmware in C and C++ for ARM-based microcontrollers and embedded Linux systems. Proven expertise in peripheral driver development for SPI, I2C, UART, and RS485 protocols in bare-metal environments. Hands-on experience with STM32 Cortex-M MCUs, Raspberry Pi 5 on Alpine Linux, and FPGA design using Verilog on Xilinx Artix-7.

Basic working knowledge of FreeRTOS. Skilled in PCB design using Altium Designer, hardware bring-up, and system-level debugging using oscilloscopes and logic analyzers.

Experience

Embedded Engineer - ITS Planner and Engineers - Greater Noida, India

(2025-02)

  • Developed embedded firmware in C for a modular real-time display system on Raspberry Pi 5 running Alpine Linux — integrated Quectel EC200U 4G LTE module, Ethernet TCP/IP stack, and RS485 communication protocol for live traffic management infrastructure.
  • Wrote low-level peripheral drivers for RS485 and UART interfaces — configured GPIO, hardware interrupts, and protocol handlers for an 8-channel lamp monitoring input card transmitting real-time fault data across distributed traffic nodes.
  • Designed layered firmware architecture separating hardware drivers, protocol handling, and application logic — reduced debugging time and enabled faster feature updates across the deployed system.
  • Developed complete firmware pipeline for a P10 LED display system (2×3 matrix) — implemented data parsing, refresh cycle control, and real-time speed visualization for vehicle-actuated traffic displays.
  • Debugged hardware and firmware issues on live deployed systems using oscilloscopes and logic analyzers — identified and resolved RS485 signal integrity issues caused by missing termination resistors, restoring reliable data transmission.

Embedded Engineer - Sharang Shakti - Gurugram, India

(2024-06 - 2025-01)

  • Developed bare-metal firmware in C++ for a custom drone flight controller — wrote SPI peripheral drivers for BMP390 and BMP585 barometric pressure sensors and Xsens MTi 9-DOF IMU, and UART driver for NEO M9N GPS module; achieved stable real-time multi-sensor fusion under dynamic flight conditions.
  • Designed Power Distribution Boards (PDBs) for 12V and 3.3V power rails using LM76005 and TPS564257 synchronous buck regulators — performed component selection, inductor sizing for 30% ripple current, output capacitor ESR analysis, and thermal validation on bench.
  • Conducted systematic hardware validation and bench testing — used oscilloscopes to verify SPI/UART waveforms, measured output voltage ripple, and iterated firmware configurations to resolve real-time sensor data errors.
  • Produced technical documentation including firmware architecture, driver API specs, component datasheets, and deployment guides for cross-functional hardware and software teams.

Embedded Engineer (Internship) - Roboverse - Delhi, India

(2023-07 - 2023-08)

  • Designed custom PCBs for HX711 load cell amplifier circuits and line-following robots in Altium Designer — delivered production-ready schematics, BOM, and manufacturing documentation.

Education

Bachelor of Technology (B.Tech) - Electronics & Communication Engineering - Jaypee Institute of Information Technology (JIIT) (2020-09 - 2024-05)

Skills

Embedded Firmware Engineer

Reviews

Related