Fidel Pina

A great communicator and hard worker. I take all my duties and responsibilities very serious. Always looking for opportunity to move up in any work establishment. Am punctual and always ready to learn new stuff and a fast learner.

Janitor at Sodexo (2024-07 – Present)

• get the trash from all assigned areas.
• sweep and mop cafeteria and clean restrooms replace toilet paper and paper towels.
• Clean offices sweep and mop them throw trash away also.
• Clean the windows from the offices also.

Janitor/Maintenance at Select Staffing (2023-07 – 2024-06)

• Clean sinks, toilets, and mop restroom floor's.
• Clean break room and microwaves sweep and mob break room.
• Throw trash away from offices break rooms and restrooms.
• Clean outside areas of establishment blow leaves, cut grass, water palm trees.

Water Jet Operator at TORAY (2023-04 – 2023-07)

• Turn machine on computer, log in select program that needs to be ran.
• Load panels onto the machine make sure they line up to stops.
• Make sure to adjust the machine to size as specified on traveler according to size.
• Start machine run one part stop after first part take it to get inspected for first article.
• When done unload reload start machine and start pulling parts off panels.
• Blow off parts with air hose place in bins when order done sign off on them in computer.
• Take to shipping and start next order.

Machine Operator at SALSA PROTOTYPE (2023-01 – 2023-04)

• I load parts onto machine to get production going.
• Check parts as they're being done to make sure part measurements are coming out according to blueprint.
• Saw cut raw material for the work orders.
• Would unload materials from truck with forklift.
• Load trucks with finish parts once wrapped.

Machine Operator at HYPER TECH (2017-09 – 2023-01)

• I work on Haas mills and fadal I also run Doosan with fanuc control lathes.
• I load parts check measurements on parts to make sure there what's on blueprint.
• I work with calipers, Od mics, high gages.
• Make adjustments on offsets when needed change tools and touch them off also when needed.
• Would unload materials from trucks with forklift and put them were they belong.

Dishwasher at Winchester Bar and Grill (2017-10 – 2018-08)

• I would collect all the dirty dishes from all the stations.
• Rinse them off and scrub them and wash them.
• Then I would dry them off and put them back to the area where they went for the cooks to grab them.

Machine Operator at CUTTING-EDGE (2015-07 – 2017-09)

• I would start up the machines in the morning and reference them.
• Run production and make sure measurements are good.
• I have knowledge using calipers, micrometers, height gage, and depth mics.
• Worked on okuma lathes and mills also doosan lathes and toyoda mill with fanuc controls.
• Make sure all machines had there oils and coolant.

Sandblaster/Painter at GENERAL MAGNA-PLATE (2013-07 – 2015-06)

• Would sandblast all parts that need to get sandblaster before they would get either nickel plated or anodized.
• Polish all the parts coming out of getting electro polished.
• I would also paint parts and spray clear coat on some parts as specified.
• Then put them in oven at temperature that parts need to cure.

Machine Operator at HAAS AUTOMATION (2011-08 – 2013-07)

• Worked on Haas machines and Mori seiki machines.
• Run production and check the tolerances.
• Check inserts on rougher tools, check endmills, and make sure drills or taps didn't break.
• Get new offsets on tools that I would replace.
• Check parts using mics, depth mics, and calipers.
• Check the coolant and oils.

High school diploma – Gateway (1999-08 – 2002-08)