Peiqing Zhu
Analog IC design engineer
Hire this person
Send a job offer directly to this candidate
About
20 years of analog IC design experience to design, test and debug analog IC 5+ years PhD education training to design, layout and test high speed PLL for Serializer Strong ability to quickly learn new knowledge and new circuits Excellent GPA grades 3.97/4.00 Demonstrated solid problem solving and analytical skill consistently solve the issues for simulation and testing in a timely and accurate manner Demonstrated innovation and creativity to design new circuits
Experience
Analog IC design engineer - Lockheed Martin Company
(2019-01)
- Design CMOS image sensors such as pixel, PLL, Serializer, Opamp, LVDS receiver, etc
- Design Error Amplifier in the Buck Circuit.
Analog IC design engineer - QST Company
(2019-01 - 2019-09)
- Design/Debugging MEMS Accelerometer and Gyroscope for mobile phone applications.
Analog IC design engineer - Freescale Company
(2014-03 - 2019-01)
- Take participating in MEMS Sensors such as TPMS (Tire Pressure Monitor System) and Accelerometer design. So be familiar with MEMS Sensor architecture, Matlab/Simulink Model for system level simulation, and verilog-AMS /verilogA model for behavior simulation.
- Design/Verification MEMS Pressure Sensor (Accelerometer) Behavior Model. Matlab/simulink and Verilog AMS and VerilogA models TPMS and Accelerometer’s behavior. In these models including MEMS sensor elements, C2V, delta sigma ADC and decimation filter signal chain.
- Debugging extreme low power consumption Temperature Restart circuit. It includes extreme low power consumption bandgap based voltage reference, which generates PTAT and constant voltages, and one comparator is used to reset MCU at high/low temperature. Various test equipments such as laser cutter, oscilloscopes, voltage/current meter, clock generator, thermal stream and probe station are used to debug this circuit.
- Design and debug the Crystal Oscillator based on TSMC CMOS technology. The oscillator contains amplitude control modulator to control oscillator output wave amplitude.
- Design Temperature Sensor used in MEMS sensor. This temperature sensor is based on continuous time delta sigma ADC structure for robust and simple. The resolution can be reach to 1oC /bit, which is accuracy enough for MEMS sensor circuit application.
- Design switching capacitor interface circuit C2V for MEMS sensor. The new architecture has been used to improve the circuit linearity. Also the full differential Opamp with input CMFB is used to maintain the common input voltage for capacitive detection. Chopping technique is used to reduce its’ offset voltage.
- Design/Verification Delta Sigma ADC in MEMS Pressure Sensor /Accelerometer. Design and debugging single loop single bit SC Delta Sigma ADC in MEMS sensor; Matlab and verilog-AMS models the Delta Sigma ADC behavior, differential Opamp and latch comparators are used in the SC Delta Sigma ADC design. In order to reduce the offset, chopping is used to mitigate the offset in the first integrator. In additional to single loop single bit SC Delta Sigma ADC also familiar with MASH and single loop multi
- Evaluated and tested Auto Gyro performance including open/closed-loop Gyro performance comparison. Be familiar with open/closed Auto Gyro design such as driver loop, sense loop, self-testing loop, and mode matching design. Also be familiar with open/close loop gyro testing such as “popcorn”, Allan variance etc.
Analog IC design engineer - Sand 9 Company (Acquired by ADI)
(2011-06 - 2014-02)
- Research and debug Temperature Compensation Circuits (TCC) Based on IBM 0.18um BiCMOS Technology. This circuit includes Gilbert Multiplier, Current Conveyor and current steering DAC.
- Design Duel Mode MEMS Oscillator, which can work in high performance mode or low power mode using Global Foundry 0.18um CMOS Technology. For high performance mode, the MEMS Oscillator exhibits excellent phase noise, and in low power mode it only consumes very low current to save power. Research and design negative input capacitance and bias regulator to increase tuning range and save power.
- Design Ring Based Oscillator Global Foundry 0.18um CMOS Technology. The Ring oscillator is designed for phase noise measurement, which includes dividers and output buffer stage.
- Design Analog and Digital LDOs Based on IBM 0.18um BiCMOS Technology. For saving chip area and pin counts, the miller feedback LDO architecture has been used for whole chip.
- Design Low Phase Noise CML Line Driver with Dual/Single Mode Output Based on IBM 0.18um BiCMOS Technology. Special noise reduction technique has been used for this line driver design to low the phase noise floor.
- Research and design High speed 8 bits Folding and Interpolating ADC Based on IBM 0.18um BiCMOS Technology. Folding and interpolating ADC architecture are used to reduce numbers of comparators to save chip area.
Analog IC design engineer - Texas Instrument
(2008-10 - 2011-05)
- Due to very large temperature coefficient of N_WELL resistor, the conventional current reference architecture no longer can be used to meet this spec. The 2nd new curvature correction architecture has been invented in this design.
- Pieces wise curvature correction technique was used to reduce the bandgap voltage variation over the temperature.
- Design Trimmable Current References and Voltage References Circuits Based on CMOS ZTC Resistor
- The ZTC resistor based trimmable current has been designed using conventional current reference architecture.
- Verification and optimization of Integrate-N/Fractional-N Charge Pump PLL
- Verification and optimization PLL basic building blocks such as PFD, Charge-pump, VCO and Pulse Swallow Divider
- Buffer LDO architecture is used to push internal low frequency pole to two high frequency poles; Thus, the buffer LDO has large bandwidth and stability to quickly response to low overshooting voltage
Research Assistant - Southern Methodist University
(2005-05 - 2008-08)
- Design 3.6GHz Radiation Tolerant LC PLL based on 0.25um Peregrine Technology Passive inductor, which is less sensitive to the radiation, has been used in the LC VCO design. Matlab code used to analysis the PLL behavior such as loop bandwidth, phase margin, transient response and noise behavior. Wideband LC VCO, which can be turned by coupling coefficient instead of Varactor, has been designed for large tuning range. HFSS tool is used to extract inductor Q factor, Ls, Rp, and Rs parameters.
- Design 1.2GHz Radiation Tolerant Self-Biased PLL based on 0.25um Peregrine Technology Robust PLL architecture, self-biased PLL, has been used for this application due to its constant damping factor and ratio of input reference frequency to bandwidth insensitive to the radiation environment.
- Design 3 GHz Fully Differential VCO and CML Dividers based on 0.25um Peregrine Technology This is the test chip used for comparison VCO performance (tuning range, jitter) variation before and after radiation. 3 GHz fully differential VCO has been designed using symmetrical load. Two kinds of CML dividers were designed: one with tail current and another without tail current to improve divider speed.
- Design 2GHz Fractional-N PLL using MASH1-1-1 Delta Sigma modulator based on 0.25um TSMC Technology Fractional-N PLL can provide fine frequency resolution at the cost of high fractional spur. MASH1-1-1 Delta Sigma modulator is used to maintain good stability.
Senior PCB design engineer - Huawei Corp.
(1998-12 - 2001-04)
- Design high speed and multilayer PCBs including net-list import, placing and routing and Gerber file output
- Familiar with Cadence Allegro tool and IBIS models to simulate PCB signal integrate including impedance match, signal qualities etc.
